Blowers

Howden 827 DVJ

The 827 DVJ dry-vacuum blower from Howden is a heavy-duty unit with integral ductile iron impellers. The casing headplates, gear cover and drive-end are gray iron. Carburized and ground spur timing gears are taper-mounted on the shaft and secured with a locknut, cylindrical roller bearings, splash lubrication on both ends and easy-to-read sight glasses for maintenance. The blower handles high inlet temperatures for rough applications. An efficient discharge jet plenum design allows cool atmospheric air to flow into the cylinder so the blower continues to run under blank-off conditions. It comes in a compact, lightweight package and delivers more than 5,700 cfm in an 8-inch gear diameter frame, as well as 28 inches Hg. 800-557-6687; www.howden.com

JFH Distributing SWAM Pneumatics blowers

SWAM Pneumatics blowers, distributed by JFH Distributing, have large bearings (SKF or FAG-Schaeffler) and large shaft diameters for longer life in rugged applications, with reduced maintenance. They promise suitable volumetric efficiency at high speed and pressure. Drop-in replacement blowers are available for Robuschi, Hibon, Roots and other brands. Horizontal-flow (or vertical-flow) blowers are available up to 6,600 CFM and vacuum up to 28 inches Hg. Blowers can be made with either mechanical seals or labyrinth/piston-ring seals. 303-279-7797; www.swam-usa.com

National Vacuum Equipment Challenger 1600

The Challenger 1600 from National Vacuum Equipment is a 1,600 cfm tri-lobe blower designed for continuous duty at maximum vacuum. It employs rotors designed to improve vacuum efficiency and reduce mechanical noise. The blower has a ballast air-cooling design and typical maximum vacuum of 27 inches Hg. 800-253-5500; www.natvac.com

Hose Reels

COXREELS V-100

With a redesigned fluid path, the V-100 Series from COXREELS offers improved O-ring sealing for greater vacuum consistency and performance, in addition to a swivel retention system that strengthens the frame and prevents separation of the swivel under excessive lateral loading. Another improvement is zinc plating of the swivel components for greater corrosion protection. It allows connection of 2-inch hose on the inlet in addition to the 1.5-inch hose. This is done by sizing the inlet to fit 1.5-inch hose on the inside and 2-inch hose on the outside. The outlet remains 1.5 inches for 1.5-inch slip hose cuffs. The reels with hose are offered in 35 and 50 foot hose lengths, but the reel itself remains unchanged. The hose has a flexible crush-proof smooth interior suitable for commercial cleaning applications, and is equipped with standard 1.5-inch threaded hose cuffs. 800-269-7335; www.coxreels.com

Hannay Reels 6000 Series

The 6000 Series manual- or power-rewind reels from Hannay Reels are suitable for applications that require longer lengths of hose like water blasting and sewer cleaning. The heavy-duty reel is available in aluminum or stainless steel construction and designed to handle daily use in the most demanding environments. A gear-driven crank rewind or a chain and sprocket drive powered rewind are available in a reliable steel hub assembly. These reels handle pressures up to 2,000 psi, with an upgrade available for pressures up to 5,000 psi. 877-467-3357; www.hannay.com

Hydroexcavation Tools

Dynablast HV420F-12VRED

The Dynablast HV420F-12VRED hydrovac water heater produces 420,000 Btu with an output temperature of 175 F at 5 gpm, making it suitable for colder climates and improved digging in clay-filled areas. All models come with ETL certification for safety, which also includes certification on the coil for higher efficiency and heat transfer, a stainless steel target plate for increased coil life and a design with serviceability in mind utilizing momentary override control. A 19- by 19-inch footprint makes it suitable for compact installations. 905-867-4642; www.dynablast.ca

Easy-Kleen Pressure Systems Wildcat Heaters

Wildcat Heaters high-pressure, oil-fired hot-water/steam heaters and hydraulic pump systems from Easy-Kleen Pressure Systems are designed for reliability and efficiency, and are installation-ready for vacuum trucks and hydroexcavators. A full range of heater options includes dry steam, redundancy packages, schedule 80 and 160 stainless steel or A53 boiler pipe, fine-tuned temperature and flow-control systems. All coils are manufactured in-house, with CRN boiler-approved coils now available. Heaters can be designed for mounting in a cabinet or supplied as a completed cabinet unit. They are CSA and ETL approved. Hydraulic pumping systems are available. 800-315-5533; www.easykleen.com

Handle-Tech pipe and hose carrying tool 

The Handle-Tech tool is designed to ease gripping, lifting and dragging pipes and hoses. It handles up to 400 pounds and holds pipes and hoses from 2 to 12 inches. Using the click-and-grip feature, the lightweight handle goes around an unwieldy hose or pipe, lifting or moving it with less effort and personal contact. It can be used in sewer pumping and cleaning, industrial vacuuming, grease handling, hydro excavation and other situations. 610-385-6091; www.handle-tech.com

Soil Surgeon hydroexcavating tool

The Soil Surgeon hydroexcavating tool fits any sewer combination truck equipped with a telescoping 6- or 8-inch boom. The tool has a 1-inch water connection. The operator controls water pressure and power through truck controls. It has a 6-foot Tuff-Tube with handles to guide the unit down for potholing or side to side for trenching. Six jets boring inward cut the soil, while six boring outward bring the tube down. 949-363-1401; www.soilsurgeoninc.com

Hydroexcavation Units

Ditch Witch HX30G

The HX30G vacuum excavator from Ditch Witch promises high-profile power in a low-profile design to ease navigation in congested and height-restricted areas. It is powered by a 31 hp Vanguard gas engine for optimal suction power and water pressure, according to the maker. To boost efficiency, it comes with a 542 cfm blower, 3,000 psi water pressure and 4.2 gpm water flow. It is offered with the choice of a 500- or 800-gallon tank to match a variety of job requirements. The machine is available in multiple trailer configurations, including the VT9 trailer that, when equipped with the 500-gallon tank, does not require a commercial driver’s license to transport. 800-654-6481; www.ditchwitch.com

GapVax HV33

Designed to safely transport water and debris in urban areas, the GapVax HV33 is shorter, smaller and more compact than its predecessor. It is 30 feet long overall on a medium-duty chassis and includes a 600-gallon water tank, 6-cubic-yard debris body, 6- or 8-inch top-mounted telescoping boom with a 14- to 17.5-foot reach, 4,000 cfm power and an inverted, full-opening tailgate. 888-442-7829; www.gapvax.com

HotJet USA Vac ’n Jet Series

The HotJet USA Vac ‘n Jet Series of vacuum trailer jetters are designed to be rugged and compact, engineered to haul equipment and spoils loads, can clean valve boxes and storm drains and hydroexcavate and/or clean drainlines and sewer lines, according to the maker. They offer hot- and/or cold-water operation with a choice of engines ranging from 13 to 66 hp and gas or diesel. They are equipped with premium triplex pumps, a 500-gallon spoils tank, 200-gallon water tank, Gardner Denver vac/blowers, 4-ton hydraulic dump and Centriclean filter system. They can also be designed to meet specifications. 800-624-8186; www.hotjetusa.com

Imperial Industries Hydro 3600 Hybrid Excavator

The Hydro 3600 Hybrid Excavator from Imperial Industries is short and compact for maneuverability in tight spaces. It is user friendly and efficient, and can be operated easily by a single person and is designed to minimize time spent on the job site, according to the maker. It includes a 3,600-gallon hauling capacity (customizable sizes available), optional water capacity, code and non-code availability, a three-stage lift hoist with built-in vibrator and full opening rear door for easy dumping, 20 gpm jetter up to 4,000 psi (adjustable), a National Vacuum Equipment 1600 blower and a moisture trap and grit ridder. Options include a 16-function remote control for easy operation of the boom, jetter, blower and vacuum. 800-558-2945; www.imperialind.com

Presvac Systems Hydrovac

The Presvac Systems Hydrovac is designed for versatility and cold-weather operation with optional full compliance with U.S. Department of Transportation specifications for collections or transportation of hazardous materials. The high-vacuum blower allows extraction of all types of soils, gravel, rock, clay, water and silt material, with knockout features in the debris tank to minimize carryover. Modular filtration configured to blower size provides blower protection and minimal maintenance, according to the maker. It comes with a heavy-duty, 8-inch boom that extends up to 25 feet with six-way hydraulic power and wireless controls for all boom functions, a soft-start water pump, vacuum breaker and truck engine speed. 800-387-7763; www.presvac.com

Rival Hydrovac T7 Tandem

The T7 Tandem hydrovac from Rival Hydrovac was designed primarily to be loaded with debris and driven within legislated road limits with most types of debris on board. The unit comes standard with a scale that reads real-time weights both in the cab and on the wireless remote to confirm weights prior to travel. An air option is available on both the T7 and T10 models. These units also have the same hydro system as any other Rival unit. This hydraulically driven compressor runs in both a low- and high-pressure range allowing for 150 psi and 150 cfm for the operating of air tools or 200 psi and 200 cfm for the operating of an air knife. 403-550-7997; www.rivalhydrovac.com

Super Products Mud Dog 700

Mud Dog 700 vacuum excavators from Super Products are designed for operator convenience and consistent performance to meet the challenges of a wide variety of applications from compact, urban projects to large-scale excavation, potholing and trenching projects. Units come standard as hydroexcavators with an optional air excavation package. The product line comes in a variety of model configurations: 700, 1200 and 1600. The 700 model was designed to be a compact unit for urban environments, with 7-yard debris capacity and 600-gallon water tank. This allows for a shorter turning radius and maximum legal payload. This unit comes standard with a dump unloading system capable of dumping into a 48-inch container. Additionally, the 700 is equipped with a rear mounted, 8-inch diameter boom that reaches 18 feet, has 270-degree rotation and can move in a 10-degree downward pivot, allowing for versatility within dig areas. 800-837-9711; www.superproducts.com

Tornado Global Hydrovacs F4 ECO-LITE

The F4 ECO-LITE from Tornado Global Hydrovacs has a 12-cubic-yard mud tank and holds 1,550 gallons of freshwater. The unit is more than 7,000 pounds lighter than the company’s older models and offers more than double the payload. The boom has a 342-degree rotation and 26-foot reach. The smaller F3 ECO-LITE is a 10-cubic-yard, 1,250-gallon tandem-axle unit that more than doubles older payload capacities. It features an 8-inch boom and 3,800 cfm blower. 877-340-8141; www.tornadotrucks.com

Transway Systems Terra-Vex HV38

The Transway Systems Terra-Vex HV38 has a 12-yard debris tank with onboard scales for efficient hauling and off-loading, and a 26-foot-by-8-inch telescoping boom. It has a one-touch-operated hydraulic half-door with a 3,800 cfm at 27 inches Hg hydraulically driven blower. Water pressure is achieved with a hydraulically driven triplex pump, delivering 10 gpm at 3,600 psi from a 1,000-gallon HDPE baffled water tank. The water is heated with a 420,000 Btu diesel-fired burner for cold-weather operation. 800-263-4508; www.transwaysystems.com

Vac-Con X-Cavator

The X-Cavator hydrovac from Vac-Con includes a cold-weather enclosure for the water systems and control panel as well as an interior area for operator seating and workspace. Unit filtration is based on the Titan combination machine, with a single-cyclone design and final cartridge-style filter. The redesigned boom is lightweight and flexible, rotating 310 degrees around the unit and moving plus 45 degrees and minus 22 degrees vertically. The durable rubber hose material can withstand harsh environments, according to the maker, and has a reach of 26 feet. 904-284-4200; www.vac-con.com

Vacall AllExcavate

AllExcavate models from Vacall efficiently remove dirt around utility lines, as well as foundations where mass excavation is not practical, according to the maker. Water pumps generate 24.5 to 120 gpm and pressures to 3,000 psi. The water system, wand, control panel, tools and worker apparel are protected in a heated compartment. Its standard AllSmartFlow CANbus intelligent control system has a programmable LCD display that monitors engine, water flow and vacuum performance, allowing for precise boom and reel adjustments. Aluminum water tanks carry 1,000 to 1,300 gallons. Options include a remote control high-dump system that raises the debris tank 76 inches and then slides it back 21 inches for dumping into roll-off containers. 800-382-8302; www.vacall.com

Industrial Vacuum Trucks

Satellite Industries Vacuum Trucks

Satellite Industries manufactures a full line of industrial vacuum trucks from 2,000 to 5,000 gallons and constructed for maximum payload capacity and improved productivity, according to the maker. They are offered in multiple chassis options, and feature vane pump or blower options. Jetter packages are also available. Customers can choose between an engine-driven 5 gpm/3,000 psi, or PTO-driven 10 gpm, 3,000 psi jetter systems. Vacuum pump options include Masport air- cooled or water-cooled models, National Vacuum Equipment air- or water-cooled models, or blowers from National Vacuum Equipment. 800-328-3332; www.satelliteindustries.com

Jet/vac combo Unit

U.S. Submergent Technologies Combination3

Combination3 trucks from U.S. Submergent Technologies include a GritGone Process for safe and fast debris removal. They include a jetter, combined vacuum and downhole system to allow users to clean while facilities remain in service with no facility shutdown or bypass pumping, remove material in submerged or surcharged conditions, reduce or potentially eliminate the need for confined space entry and paint-filter dry material, ready for disposal, with the GritGone Process. Trucks offer an extended reach with a 49-foot extendable boom. 844-956-1129; www.ussubmergent.com

Vacuum pumps

Fruitland 870 Series

Fruitland’s 870 Series pump allows vacuum levels of 28.5 inches Hg and continuous vacuum of 27 inches Hg. Additionally, it is capable of providing 30 psi pressure for off-loading. Oil consumption is 1 gallon for 18 hours of operation to reduce consumption and environmental impact. Locally sourced, non-proprietary oil may be used. The pump delivers 510 cfm (free air) through 4-inch porting. 905-662-6552; www.fruitlandmanufacturing.com

Masport TITAN

The TITAN vacuum/pressure pump from Masport has a washable stainless steel inlet filter for long filter life, integral mounting bosses for alignment with the gearbox and hydraulic mount, an automatic adjustment-free mechanical oil pump and heat-stabilized Kevlar vanes machined to exacting tolerances. It can achieve a minimum of 407 cfm at 27 inches Hg and is fan-cooled for higher continuous vacuum operations. It has heavy-duty bearings, Viton oil seals, vane-wear inspection ports and durable translucent high-temperature oil lines that allow visible flow of oil to the pump. End thrust protection prevents rotor-to-end-cover contact created by direct PTO drive or misaligned belt-driven systems. It comes with 3-inch NPT bolt-on valve flanges for ease of installation, a 1/4-inch NPT vane flush port, integral vacuum relief valve, an integral valve that allows the pump to operate in vacuum and pressure mode and O-ring end covers that eliminate air or oil leakages. 800-228-4510; www.masportpump.com

Moro USA W Series PM80W

The W Series PM80W liquid-cooled vacuum pump from Moro USA is suitable for a wide variety of applications, including oil and gas, septic, and industrial, according to the maker. It has oiled bearings that don’t require additional maintenance, a sealed positive displacement direct-feed oiling system, Kevlar vanes, an integrated check valve and a changeover valve. A jacketed casing provides liquid cooling, allowing a deeper continuous-duty vacuum. A coolant pump is available for self-contained packages. It includes industrial-duty Viton oil seals and is available in clockwise and counterclockwise rotations. 866-383-6304; www.morousa.com

Wallenstein Vacuum 753 Series

The 753 Series vacuum pump from Wallenstein Vacuum incorporates wide vanes that allow up to an inch of wear, designed for longer service life. It provides 422 cfm airflow at 1,200 rpm and is precision-machined for vacuum levels up to 28 inches Hg. Options include air-, liquid- or dual-cooling systems where air injection is combined with liquid cooling. A pump-flushing port is included on the top valve for convenient maintenance. The quick-access housing end plate allows for easy internal inspection with no bearings to pull. Oil lubrication is via a mechanical piston pump driven by shaft rotation or available with a sight-feed valve oil regulator system using vacuum/pressure to draw oil with no moving parts. 800-801-6663; www.wallenstein.com

Westmoor Conde PowerPaks 

Westmoor Conde PowerPaks are preassembled, gasoline or diesel-powered vacuum pump units. They are easy to install, according to the maker, and include a heavy-duty steel base with aluminum diamond plate trim and belt guard. Rigid assembly is designed to ensure minimum vibration and maximum power. They are available with either vacuum only or vacuum/pressure pumps. A wide range of cfm options ensure the PowerPak is matched to the tank size and application. Units are powered with optional Honda GX Commercial Series gasoline engines or Hatz industrial air-cooled diesel engines. Units can be easily transferred to another tank system when needed. 800-367-0972; www.westmoorltd.co